How to install Yarn sensor ?-KJTDQ Sensor

Be the Best Sensors’ Manufacturer and One Stop Solution Service

Attn:Tara Email:kaijite3@kjtsensor.com WhatsApp:+86 13951751584

Magnetostrictive sensor

How to install Yarn sensor ?

2020-09-18

How to make sure Yarn sensor is installed properly to get the most out of it is important for our customers. This product is manufactured to provide industry-leading performance and beauty but should be installed by following the instruction manual to ensure it works properly. Failure to install it with all of these requirements may lead to product damage. Improper installation will also void the warranty of this product, so be sure to discuss and understand the install process with Nanjing KJT Electric Co,.LTD service team if you have problems.
KJTDQ Array image339

KJTDQ Array image339

KJT has obtained high compliments among customers at home and abroad. According to the material, KJT's products are divided into several categories, and limit switch is one of them. KJTDQ fiber optic signal amplifier is designed by a team of experienced experts using the latest design concept based on a strict design process. It can detect and respond quickly to some types of input. With the regular maintenance, the product is able to work as efficiently as possible and could last for many years. It has been widely used for packaging and plastics machinery, production lines, and conveying systems.
KJTDQ Array image339

KJTDQ Array image339

our company will maintain technological benefits and supply thoughtful and innovative answers. Get an offer!

Custom message

Related Products

KJTDQ-EX34H35-LY - VRS Sensor for use in Explosive Atmospheres w/3/4-20 UNEF-2A 3.5" Thread & 10′ Leads Variable Reluctance Speed (VRS) sensors

The KJT-EX34H35-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply. The EX34H35 is specifically designed for use in explosive atmospheres.

M16 high pressure proximity sensor 500bar L=73mm with M12 connector

M6 fiber sensor through beam PNP/NPN Sn=0-1000mm nickel plated brass

M12 high pressure proximity sensor shielded NPN PNP NO NC NC+NO

M6.5 ultra small inductive proximity sensor unshielded PNP NPN NO NC L type

KJT-SHN11.GK12.E4-LY 1-Channel Hall M14 Heavy Duty Speed Sensors

1-Channel Hall M14 Light Duty series Data summary: Power supply 8 VDC ... 36 VDC Frequency range 0 Hz ... 15 kHz Operation temperature -40 … +125°F

KJT-3030AN40-LY Speed Sensors 15.9 mm 190V High Output

High Output VRS sensors are designed for use in applications where higher output voltages are needed. They perform best at low to medium speeds with medium to high impedance loads. Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux lines of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (

KJTDQ- KJT-EV58S40-LY - VRS Sensor w/Amplifier - Square Wave Signal Output from NPN w/5/8-18 UNF-2A 4.0" Thread & 39" Leads Variable Reluctance Speed (VRS) sensor

The KJT-EV58S40-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet and an amplifier. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The signal is converted to a square wave signal with constant amplitude by the integrated amplifier. The frequency of the output signal is proportional to the speed of the moving target.

M18 Laser photoelectric sensor through beam type

Ring proximity sensor ABS NPN PNP NO NC Sn=0-5mm connector

M12 inductive proximity sensor unshielded AC NO NC Sn=4mm IP67

M30 inductive proximity sensor shielded AC NO NC Sn10mm

M30 Namur proximity sensor

KJTDQ-3045A-LY VRS Speed Sensors 15.9 mm 300V High Resolution

High Resolution VRS sensors are designed for use in applications where precise timing pulse is required, and/or fine pitch gears are used. Proper alignment of the sensor is required. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals.

KJT-E16A25-LY - VRS Sensor w/M16x1.5 2.5" Thread

The KJT-E16A25-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply.

Yarn capacitive sensor DU3B NPN PNP NC for textile

Squre Type Q31 Laser Infrared Beam Sensor with 50m Distance

Belt Conveyor Protection Deviation Switches

KJT-SHP7.GP05.SB-LY 1-Channel Hall M18 Brass Speed Sensors

KJT-SHP7.GP05.SB-LY 1-Channel Hall M18 Brass Speed Sensors

KJT-MA3055-LY Speed Sensors VRS 1/4X.7 450F BTTP 28GA LDS

High Temperature VRS sensors are designed for use in applications where the sensor is exposed to temperatures up to 260 ºC [450 ºF]. Sealed Front-End versions are available for applications where the sensor is exposed to fluids, lubricants or adverse environmental conditions. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs a

KJTDQ-EX58AM25-LY - VRS Sensor for use in Explosive Atmospheres

The KJT EX58AM25 series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply. The EX58AM25 is specifically designed for use in explosive atmospheres.

M12 high pressure proximity sensor 500bar L=78mm with M12 connector

Ring proximity sensor ABS NPN PNP NO NC Sn=0-8mm Connector M8

M30 high temperature proximity sensor shielded PNP NPN NO NC -25℃-+150℃

M30 inductive proximity sensor unshielded AC NO NC long distance

KJT-3070A35-LY Speed Sensors Explosion Proof 60V VRS Sensor

DESCRIPTION Hazardous Location VRS sensors are designed for use in locations where explosion-proof or intrinsically safe sensors are required. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor's pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave

KJT-F58S-LY - Hall Effect Zero-Speed Sensor - Square Wave Signal Output from NPN w/ 5/8-18 UNF-2A 2.0" Thread & 39" Leads

The KJT F58S series Hall-Effect Zero-Speed sensors are suitable, in conjunction with a ferrous pole wheel, for generating square wave signals proportional to rotary speeds. The F58S exhibits a static function, whereby pulse generation down to 0 Hz is guaranteed. The sensor function is independent of the rotational mounting angle.

M12 capacitive proximity sensor shielded PNP NPN NO NC Sn=1-3mm IP67

M3 fiber optic sensor diffuse PNP/NPN Sn=0-80mm stainless steel fibre optic probe

M12 high pressure proximity sensor shielded NO NC NO+NC IP68 connector

M30 inductive proximity sensor unshielded PNP/NPN NO NC Sn15mm

KJT-SNG-QPDB-000-LY Speed Sensors Magspeed Quadrature Speed Sensor

KJT's SNG-Q Series Quadrature Speed and Direction Sensors are designed to provide both speed and direction information. Speed information is provided from digital square wave outputs; direction is provided using a quadrature output with signals 90° phase shifted from each other. With the quadrature output, target direction is determined by output lead/lag phase shifting.

KJTDQ-KJT-SNG-SPRD-003-LY Speed Sensors HALL SENSOR, RIGHT ANGLE, 67MM

KJTDQ's SNG-S Series Speed Sensors use a magnetically biased Hall-effect integrated circuit (IC) to accurately sense movement of ferrous metal targets. The specially designed IC and a permanent magnet are sealed in rugged, probetype packages. The IC detects the alteration of the magnet's flux density when it is approached by ferrous metal. A sensor positioned at the circumference of a revolving gear wheel detects the teeth and spaces, and supplies a digital pulse output with frequency proportional to gear wheel speed. Optimum performance is dependent upon a combination of variables such as target material, geometry and speed, sensor/ target gap, and environmental temperature.

M18 capacitive proximity sensor shielded PNP NPN NO NC NO+NC

M4 fiber quality sensor through beam PNP/NPN Sn=1m stainless steel optical sensor

M12 capacitive proximity sensor shielded 10-36VDC PNP NPN NO NC IP67

M30 inductive proximity sensor unshielded DC NO NC Sn25/40mm

KJT-ST series basic photoelectric switch 671/674

KJT-ST series sensor is a basic photoelectric sensor product independently developed and produced, integrating photoelectric conversion circuit, amplification circuit, logic processing circuit and drive output circuit. Compared with similar foreign products, it has the advantage of low price, fast response, high precision and stable quality. It is suitable for robots, automatic production lines, lathes, manipulators and mechanical arm components, food processing equipment, printing equipment and other industrial machinery and equipment.

KJTDQ-F16S40-LY - Hall Effect Zero-Speed Sensor Square Wave Signal Output from NPN w/M16x1.5 4.0" Thread & 39" Leads

The KJT F16S40 series Hall-Effect Zero-Speed sensors are suitable, in conjunction with a ferrous pole wheel, for generating square wave signals proportional to rotary speeds. The F16S40 exhibits a static function, whereby pulse generation down to 0 Hz is guaranteed. The sensor function is independent of the rotational mounting angle.

M12 high pressure proximity sensor 500bar L=93mm with M12 connector

Ring shape inductive proximity sensor ABS NPN PNP NO NC Sn=0-12mm IP67 connector m8

M30 high temperature proximity sensor unshielded PNP NPN NO NC -25℃-+150℃

KJT-BTL7 -P- Series - Analog voltage Magnetostrictive linear position sensors in profile housing

KJT-BTL7 -P- Series - Analog voltage Magnetostrictive linear position sensors in profile housing

KJT-SNG-QPDB-002-LY Speed Sensors Magspeed Quadrature Speed Sensor

KJT's SNG-Q Series Quadrature Speed and Direction Sensors are designed to provide both speed and direction information. Speed information is provided from digital square wave outputs; direction is provided using a quadrature output with signals 90° phase shifted from each other. With the quadrature output, target direction is determined by output lead/lag phase shifting.

KJTDQ-KJT-EV58S25-LY - VRS Sensor w/Amplifier - Square Wave Signal Output from NPN w/5/8-18 UNF-2A 2.5" Thread & 39" Leads Variable Reluctance Speed (VRS) sensor

The KJT-EV58S25-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet and an amplifier. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The signal is converted to a square wave signal with constant amplitude by the integrated amplifier. The frequency of the output signal is proportional to the speed of the moving target.

M5 Laser photoelectric sensor diffuse type

M8 inductive proximity sensor shielded 10-36VDC PNP NPN NO NC Sn=1mm

PNP No 10-36V M12 High Pressure Proximity Sensor with M12 Connector-

KJT-MA240SAN-LY Speed Sensors 15.9 mm 60V High Output

High Output VRS sensors are designed for use in applications where higher output voltages are needed. They perform best at low to medium speeds with medium to high impedance loads. Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions.

KJTDQ-SNG-QPLA-000-LY Speed Sensors Quadrature, 35mm Right Angle Exit

KJT's SNG-Q Series Quadrature Speed and Direction Sensors are designed to provide both speed and direction information. Speed information is provided from digital square wave outputs; direction is provided using a quadrature output with signals 90° phase shifted from each other. With the quadrature output, target direction is determined by output lead/lag phase shifting.

M18 capacitive proximity sensor Unshielded NO NC NO+NC Sn=1-15mm

M6 fiber sensor through beam PNP/NPN Sn=1m stainless steel

M30 high temperature proximity sensor unshielded PNP NPN NO NC connector

KJT-BTL C1 - Profile PA - IO-Link Magnetostrictive linear position sensors in profile housing

KJT-3040AN40-LY Speed Sensors VRS M5K 5/8-18X4.0 MS CONN

Power Output VRS sensors are designed for driving low resistance loads at large air gaps in applications where larger actuators may be used. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux lines of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor's pole piece. If a standard gear were used as a target, this output signal would resemble a sine w

Kjtdq-Kjt- E38S-LY - VRS Sensor w/3/8-24 UNF-2A 1.35" Thread & 39" Leads Variable Reluctance Speed (VRS) Sensors

The KJT-E38S-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply.

High temperature limit switch XWKF

M22 high pressure proximity sensor shielded PNP NPN NO NC NO+NC IP68

M30 inductive proximity sensor unshielded DC NO NC connector

KJT-GS100502-LY Speed Sensors HALL EFFCT 6mA 24VDC M12-1 20AWG ALUM

The GS1005-GS1007 series gear tooth speed sensors are Hall Effect devices designed for use in applications where ferrous edge detection/near zero speed sensing is needed. They provide a sinking current output.

KJTDQ-KJT-EX34H-LY - VRS Sensor for use in Explosive Atmospheres w/3/4-20 UNEF-2A 1.9" Thread & 10′ Leads Variable Reluctance Speed (VRS) sensors

The KJT-EX34H-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply. The EX34H is specifically designed for use in explosive atmospheres.

M3 Laser photoelectric sensor diffuse type

M8 inductive proximity sensor unshielded 10-36VCD PNP NPN NO NC

M4 ultra small short inductive proximity sensor shielded unthreaded PNP NPN

KJT-3050S10-LY Speed Sensors 6.4 mm 12V General Purpose

DESCRIPTION General Purpose VRS sensors are designed for use in applications with medium to high speeds or in electrically noisy environments with relatively small air gaps. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor's pole piece. If a standard gear were used as a target, this output sig

KJTDQ EX58AM40 - Variable Reluctance Speed (VRS) sensors w/5/8-18 UNF-2A 4.0" Thread

The KJT-EX58AM40-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply. The EX58AM40 is specifically designed for use in explosive atmospheres.

M6 Laser photoelectric sensor diffuse type

M8 inductive proximity sensor unshielded DC PNP NPN NO NC Sn=4mm/6mm

M30 inductive proximity sensor unshielded DC NO NC Sn15mm connector

KJT-GS101202-LY Speed Sensors HALL 24VDC Flnge Mnt 22 AWG X1m BBB Cble

Speed Sensors HALL 24VDC Flnge Mnt 22 AWG X1m BBB Cble

KJTDQ-KJT-EX10A-LY - VRS Sensor for use in Explosive Atmospheres w/M10x1 1.3" Thread Variable Reluctance Speed (VRS) sensors

The KJT-EX10A-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply.

High temperature limit switch XWKB

M18 high pressure proximity sensor shielded PNP NPN NO NC Sn=1.5mm

KJT-BTL6 -PF- Series - Analog current Magnetostrictive linear position sensors in profile housing

KJT-BTL6 -PF- Series - Analog current Magnetostrictive linear position sensors in profile housing

KJT-3015A35-LY Speed Sensors VRS M3L 3/8-24X3.5 24 LDS

General Purpose VRS sensors are designed for use in applications with medium to high speeds or in electrically noisy environments with relatively small air gaps. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor's pole piece. If a standard gear were used as a target, this output signal would re

KJT-E16A-LY - VRS Sensor w/M16x1.5 1.5" Thread

The KJT-E16A-LYseries Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply.

M3 fiber optic sensor diffuse PNP/NPN Sn=0-60mm stainless steel optical sensors

M30 low temperature proximity sensor shielded NO NC Sn=10mm

KJT-SHP10.GN03.E1-LY 1-Channel Hall M16 Speed Sensors

KJT-SHP10.GN03.E1-LY 1-Channel Hall M16 Speed Sensors

KJTDQ-3070A-LY Speed Sensors Hazard Location VRS 40kHz 78mm

Hazardous Location VRS sensors are designed for use in locations where explosion-proof or intrinsically safe sensors are required.Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux lines of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor's pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if view

M14 high pressure proximity sensor 500bar L=65mm with M12 connector

M12 Hall Proximity Sensor , Gear Speed Sensor For Hydraulic Motor

M6.5 ultra small inductive proximity sensor shielded unthreaded L=18mm

KJT-SNDH-T4P-G02-LY Speed Sensors 45mm Barrel, 4.5Vdc 1 Hz to 15kHz,OpFreQ

KJT-SNDH-T4P-G02-LY Speed Sensors 45mm Barrel, 4.5Vdc 1 Hz to 15kHz,OpFreQ

KJTDQ-KJT-E58A25-LY - VRS Sensor w/5/8-18 UNF-2A 2.5" Thread Variable Reluctance Speed (VRS) sensors

The KJT-E58A25-LY series Variable Reluctance Speed (VRS) sensors consist of an iron core, an inductive coil and a permanent magnet. A ferrous pole wheel passing the sensor face changes the magnetic field strength, resulting in an AC Voltage being induced in the coil. The frequency of the output signal is proportional to the speed of the moving target. The amplitude of the signal depends on speed, air gap, geometry of the target, magnetic properties of the target material and the electrical load. VRS sensors, also known as passive or electromagnetic sensors, do not require an external supply.

M30 low temperature inductive proximity sensor unshielded 10-36VDC NO NC

M30 low temperature proximity sensor shielded NO NC connector IP67

KJT-SHN11.GK13.SC-LY 1-Channel Hall M14 Heavy Duty Speed Sensors

1-Channel Hall M14 Light Duty series Data summary: Power supply 8 VDC ... 36 VDC Frequency range 0 Hz ... 15 kHz Operation temperature -40 … +125°F

KJTDQ-F58S40-LY-Hall Effect Zero-Speed Sensor-SquareWaveSignalOutputfromNPNw/5/8-18UNF-2A4.0";Thread&39"Leads

The KJT-F58S40-LY series Hall-Effect Zero-Speed sensors are suitable, in conjunction with a ferrous pole wheel, for generating square wave signals proportional to rotary speeds. The F58S40 exhibits a static function, whereby pulse generation down to 0 Hz is guaranteed. The sensor function is independent of the rotational mounting angle.

KJT--DSK41900 zero speed Hall effect sensors PNP NPN

M8 inductive proximity sensor unshielded 10-36VDC NO NC Sn=2mm

KJT-BTL7 -P- Series - Analog voltage Magnetostrictive linear position sensors in profile housing

KJT-BTL7 -P- Series - Analog voltage Magnetostrictive linear position sensors in profile housing

KJT-3030AN30-LY Speed Sensors 15.9 mm 190V High Output

High Output VRS sensors are designed for use in applications where higher output voltages are needed. They perform best at low to medium speeds with medium to high impedance loads. Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions.

M8 capacitive proximity sensor shielded PNP NPN NO NC Sn=1mm IP67

M6 laser sensor diffuse PNP NPN NO NC Sn=150/200mm adjustable

M3 ultra small short inductive proximity sensor shielded long sensing distance

KJT-3050A20-LY Speed Sensors 6.4 mm 12V General Purpose

General Purpose VRS sensors are designed for use in applications with medium to high speeds or in electrically noisy environments with relatively small air gaps. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor's pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor's pole piece. If a standard gear were used as a target, this output signal would re

M12 Namur proximity sensor

M18 photoelectric sensor retro reflection PNP NPN NO NC NO+NC Sn=2m adjustable

M4 ultra small inductive proximity sensor shielded unthreaded PNP NPN

Nanjing KJT Electric Co,.LTD

Our main products are proximity sensor, photoelectric sensor,speed sensor,wireless sensor and so on.

CONTACT US

kjt sensor manufacturer

Copyright © 2019 Nanjing KJT Electric CO.,LTD | All Rights Reserved Design

Chat Online 编辑模式下无法使用

Leave Your Message inputting...

Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.

*Name：

*Phone：

*E-mail：

*Content：